
The emergency or parking brake whichever you call is a part of a safety system as it prevents the car from rolling away. Furthermore, it also prevents putting an excessive load on your vehicle’s transmission. Read to find out more about how to adjust emergency brake on Chevy Silverado.
We all know Chevy Silverado. This truck is built by Chevrolet for any lightweight duty. Moreover, Chevrolet also released a 2020 version of the following truck. Silverado is a favorite truck among truck users due to its high-strength Durabed, trailing technology, and multiple trim levels.
The parking brake completes multiple roles mandatory for vehicle safety. Admittedly, the emergency brake is not for drifting. Moreover, it is not an emergency brake. This tech is made to prevent your truck from rolling away while it is parked on the gradient.
Sometimes, you might need to adjust the emergency brake on your Chevy Silverado. This is because you might have applied your parking brake, but still, your truck starts to roll.
So save your time. Repair your vehicle at home with our point-to-point guide. You will need a few tools while doing the whole process. Then you will also need a place to raise your Chevy Silverado. Also, You can use this article for all years of Chevy Silverado. Meanwhile, check out our expert review on theĀ best tuner for 6.7 Cummins.
Learn more about how to adjust the emergency brake (e-brake) on Chevy Silverado below.
Adjusting steps of emergency Brake on Chevy Silverado
We have made an article by keeping in mind that it should be on a point article. This will prevent our viewers from losing interest. So, How do you adjust the parking brake on a Chevy Silverado? The adjusting steps are listed below.
Primary step
Loosen the lug nuts. Use a wrench to lose the rear lug nuts partially. Finally, find the impeccable spot you can notice in front of the rear wheel to place your Jack.
Lift the truck about 6 inches. Now use the lug nut wrench to remove the nuts entirely. Then, dismount the tire. Be sure to support the truck with jack stands. Not doing so will make the truck collapse.
Secondary step
In this step, the first work to do is to dismount the brake calipers from the rotor itself. Dismounting so will let you gain access to the adjusting mechanism for the parking brake. To dismount the caliper, you will use a ratchet wrench.
To give a counter-balance for one of the top bolts, you might need a 5/8 open wrench. Remove the three bolts and use your hand to slide out the caliper off of the rotor.
Finally, slide the rotor off to reveal the parking brake mechanism.
Tertiary Step
You have successfully exposed the parking brake mechanism. Now, look at the brake assembly. Refer to the rotary dial. It is located between 12 and 1 o’clock.
Furthermore, you will notice one thing. The turn dial is connected to a bolt. That bolt pushes out the parking brake shoes. Pushing so allows the shoe to come closer to the rotor to tighten up the brake tension.
Adjust this dial with the help of Oiler’s until the shoes are further up than their current state. Do tighten coupled turns at a time. Test the resistance by assembling the rotor back. At the same time, observe how much more friction there is between the pads and the rotor.
If there is no enough friction, then remove the rotor and turn the dial further. Repeat the process until corrected. Remember not to tighten up the parking dial to a high magnitude as this might disrupt the balance. Be sure to be precise while doing all the processes.
Also, tightening up too much can break delicate parts. You don’t want that to happen. Breaking a part will cost you a ton of dollars. The result? Pocket empty!
Quaternary step
The final step! Moreover, this is a wrap-up step. You will need to assemble back all the parts that you took off. Simply reverse the process of opening. We have sorted the process into bullet points to ease your life. Hopefully, the final process will solve your problem, and you will be able to run your truck as usual.
Although after finishing the process, do visit a car mechanic when possible. This is to check the wheel alignment. Opening the parts might disrupt the wheel alignment. Although this is not a severe issue and will not cause an accident, so relax and donor worry. But do visit a mechanic when you have time. This is for the betterment of your car.
If your car’s wheel alignment is not perfect, performance will be sacrificed. And we know you didn’t buy a Chevrolet to sacrifice performance. The reverse process is listed below. Go through them.
- Mount the rotor
- Install and bolt down the caliper
- Mount the tire
- Tighten the lug nuts with a hand
- Lower down the car
- Tighten the lug nuts with a wrench
- Finally, you have a safe parking brake. Congratulations!
Items you will need
- Jack
- Jack stands
- Wrench
FAQ about Parking Brake Adjustment
Will adjusting the parking brake stops the car from rolling?
Answer: Yes sir, if your brake pads are not decayed due to natural wear and tear. If your brake pads are decayed, you will need immediate replacement.
Not replacing might result in brake failure leading to an accident. Please see a car mechanic soon.
why is my parking brake stuck?
Answer: There are several reasons for this. Cold weather can freeze your vehicle brake. Rust and corrosion can also be a good reason. If your parking brake was held for too long then it can also be a reason. Your parking brake can be engaged too hard by you. It can also be a reason.
Your Vehicle brake is stuck due to all these reasons. A question arises then how to release the emergency brake when stuck. Call your car mechanic in such a scenario.
Conclusion
This is all about our today’s topic. We hope our article was useful to you. Furthermore, for your ease, we have kept our points short and on point.
If you were successful, congratulations. Although, if you were unsuccessful, show your car to a mechanic.
Remember to go to a car dealer certified mechanic or known mechanic. Going to some random mechanic might make the situation even worse.
Parking brakes or emergency brake whatever you call is an important part of your car. Never ignore anything regarding this sensitive area. Be sure to always visit a car mechanic once a month even if you have no problem. This will minimize future problems and will keep your car like new!
You can read our recent review on how to start dodge ram 1500 without key.
Leave a Reply