We are pleased to offer you today our article about how to install coil spring spacers. Without a doubt, coil spring spacers enhance the performance of your vehicle. Furthermore, the coil spring spacers are for those who don’t want the compromise of coil performance.
The coil enhances vehicle performance. But there are several factors to consider before installing the coil spring spacers. You should know some of the basics before installation. First of all, you should understand what coil springs are. You should know coil spring spacers are good or bad for your vehicle.
You can check out our other product reviews on the best fuel pumps for carb & the best cam for 5.3 Vortec.
So now, let’s dive into the details.
Facts & The Installation Guide of Coil Spring Spacers
The coil spring spacers lift your vehicle. At this point, you might have a question. Do I need to replace my factory-built suspension? The answer is no. Moreover, This is the magic of coil spring spacers. You don’t need to replace your vehicle’s inbuilt suspension to raise your vehicle’s ground clearance.
Furthermore, the coil spring spacers are for those who want higher ground clearance for their vehicles. The spring spacers are fitted just above the suspension of your car. Moreover, coil spring spacers are not whooping expensive to buy.
Coil Spring Spacer Problems
The coil spring spacers are very useful. But every good thing consists of a bad thing. So let’s dive in with the problem of installing coil spring spacers.
What Are The Problems?
Vehicle manufactures spend years designing a car. They have to consider several factors before they develop a vehicle. One of the most critical factors is the Centre of gravity. Moreover, CentreCentre of gravity of a vehicle impacts the degree of turning radius.
Coil spring spacers impact the CentreCentre of gravity. As the spacer increases the ground clearance level, the CentreCentre of gravity of the vehicle rises. Rising the CentreCentre of gravity reduces the turning radius angle of your car.
What this means is you will be able to turn your vehicle at a slower speed than usual. If you turn your vehicle faster, there will be a high chance that your vehicle will flip over, causing an accident.
Installing coil spring spacers also reduces your vehicle balance. Furthermore, Your car will shake more than usual at a higher speed. Thus, it will affect your driving confidence. Your vehicle will be less confident on the road.
Check Out: The Best Garage Door Opener.
Now let’s see how to install the coil spring spacers.
How To Install Coil Spring Spacers?
Before we dive into how to install spring spacers, let’s know the benefits of spring spacers.
- Coil spring spacers cost-effective
- They are versatile
- They make a guaranteed lift for a limited amount.
- Easy installation process
- The rates of the spring are steady
We have added coil spring spacer installation instructions for your convenience. The steps are given in step by step.
Use the jack to lift your vehicle to a workable height. Now lose all the nuts of the wheel. Remember to lose nuts at a time. Do not open the wheel.
Repeat the process of losing all the lug nuts of the four wheels. Then use a frame to raise your vehicle.
Use factory-made lift pads to lift your vehicle. This is to avoid damaging your vehicle components. Remember not to keep the jack in an axel as it will be necessary to swing the suspension freely.
Place the jack stands under a frame. This is to give support and low your vehicle.
Furthermore, the jack stands will be useful to elevate the axle.
Place the jack under the axle to raise it. This will balance some overall weight. Moreover, it will keep the suspension damage free of damage. This is because the shaft is freely hanging.
Remember, you had loosened all the lug nuts of the tire. Now what you will do is remove the tires. Make sure that the axel is held lightly by the jack.
Remove the shock absorbers and keep it under your car.
Remove the cotter pin from the sway bar nut. Now remove the screws of the castle nut from the ending link of the sway bar.
Disconnect the sway bar link using a hammer. Also, use a ball and joint separation tool.
Use a spring compressor to protect the spring. Now lose the components. Before doing so, detach the coil retainers.
Lower the axle. Be careful not to fall off the jack. Now insert the coil spacer on the top of the spring.
Raise the jack slowly so that the spring spacer comes in contact with the frame plus the axle.
Now attach the coil spring retainers. Do the reverse process of disassembling.
What makes our article stand apart from our counterparts?
We have experienced writers who write each and every article after a certain level of research. You will never find a unique article as we provide. So be assured that you are getting the right advice from us.
We hope by now you know the details on the installation of coil spring spacers. Furthermore, we have added step by step guide on how to perform the process.
Before installation, please read all the contents of the article. There is a problems section where all the problems related to coil spring spacers are written. Moreover, there is also a section of what are the benefits of using coil spring spacers.
Do consider all the points. Remember installing coil spring spacers might void your car warranty. Contact the dealer before doing so if you are not sure.
You can question that are coil spring spacers safe. Please be careful during the installation. Your car has fragile parts. Hence treat them delicately. Not sure if you can do this? Feel free to contact a car mechanic to do it for you. They will be happier to assist you.
Remember to go to a certified car mechanic. Moreover, there are lots of car mechanics today. Most of them are inexperienced and just do business. Furthermore, They have no proper goal or target. Hence visit a certified mechanic so that you will remain relaxed that your car is in safe hands.
You can read our article on what is the towing capacity of a Toyota tundra?
Leave a Reply